|
ICStation.com is an online store which specializes in all kinds of IC products, such as electronic devices and components, development modules, development boards, consumptive materials and so on.
Translate
2013年9月25日星期三
National Day Sale: 12% OFF on All Modules & Development Board + Free Gift
2013年9月24日星期二
Warm White 5M 16FT Waterproof 5050 SMD LED Strip 300 LEDs
Color: White
Model: 5050-60 Beads
Power: 14.4W / m
Voltage: 12V
Dimension: 8mm (W) * 5000mm (L)
LED Quantity: 300 leds/5 Meter
Model: 5050-60 Beads
Power: 14.4W / m
Voltage: 12V
Dimension: 8mm (W) * 5000mm (L)
LED Quantity: 300 leds/5 Meter
Digi LCD Voltmeter Ohmmeter Ammeter Multimeter Tester OHM VOLT
DT830B 3 1/2 digital multimeter,
the most popular type of digital multimeter whichfully meet
the general requirements. Colleges electronics, computer, information specialty
excellent student internships supplies.Suitable for laboratory, factory, school,
hobbies, electricians, families and DIY users.
- Product Model: DT830B (comply with CE / GS)
- Full compliance with GS / CE standard DT830B
- 3 1/2 digit LCD display value 1999
- Low voltage symbol display
- Overload
- Diode and triode measurement
- Power Supply: 6F22 9V battery
- Display Size: 16 x 48mm
- Maximum Display: 1999
- Dimensions: 126 x 70 x 24mm
2013年9月23日星期一
MAX7219 Dot Matrix MCU Control Display Module DIY Kit for Arduino
Module parameters:
1.A single module can drive an 8 * 8 common cathode lattice
2.Module Operating voltage: 5V.
3.Module size: 5 cm long X 3.2 cm wide X 1.5 cm high
4.With four screws hole, aperture 3mm, by using our M3 Tongzhu fixed
5.Module with input and output interfaces, supports multiple modules cascade
Wiring instructions:
1.The module left as an input port to the output port on the right.
2.The control of a single module, simply input port to the CPU
3.Multiple modules cascade input termination CPU, 2 output termination module, a module of the input of the input terminal, the output terminal of the first two modules of the first three modules, and so on ...
51 MCU, for example:
VCC → 5V
GND → GND
DIN → P22
CS → P21
CLK → P20
1.A single module can drive an 8 * 8 common cathode lattice
2.Module Operating voltage: 5V.
3.Module size: 5 cm long X 3.2 cm wide X 1.5 cm high
4.With four screws hole, aperture 3mm, by using our M3 Tongzhu fixed
5.Module with input and output interfaces, supports multiple modules cascade
Wiring instructions:
1.The module left as an input port to the output port on the right.
2.The control of a single module, simply input port to the CPU
3.Multiple modules cascade input termination CPU, 2 output termination module, a module of the input of the input terminal, the output terminal of the first two modules of the first three modules, and so on ...
51 MCU, for example:
VCC → 5V
GND → GND
DIN → P22
CS → P21
CLK → P20
ADXL345 3 Axis Digi Accelerator Gravity Tilt Module for Arduino
Feature
- Module: adxl345 module (three-axis acceleration of gravity)
- Chip: the adxl345
- Power supply :3-5V
- Means of communication: the iic / spi communication protocol
- Measuring range: ± 2g ± 16g
- Schematics, manuals and reference documentation of relevant data
- 51, the avr, the arduino microcontroller test code
- 3-axis, ±2g / ± 4g / ± 8g / ±16
2013年9月22日星期日
DC 4.5-30V 0-50A Dual LED Digital Volt Meter Ammeter AMP Power
Product Features:
1.The small size of the two-color dual instrument.Voltage and current can be displayed on the same screen at the same time
2.This instrument test voltage, current, power supply is taken from the test loop.No additional power supply
3.The the instrument test voltage supply range: DC4.5 ~ 30V,The reverse does not burn,
Note: The maximum input voltage can not exceed 30V, otherwise there is the danger of burned
4.The instrument is equipped with five wiring.Convenient access to car / battery car / motorcycle car line,,Used to monitor the battery voltage,,Grasp the battery voltage state,can also be used for other products, the use of Voltage/current measurement.
Wiring Method:
The instrument with five lines:
Thin black line: Header supply ground
The Thin Red Line: Header powered regular (Note, thin red and black line between the voltage can not exceed 30V)
Thick black lines: public test end
Thick red line: measuring the positive voltage input terminal
Yellow lines: current input terminal; header uses of design, the measuring end of the ground and the ground of the power supply side is the same, it is only then measured the back of the device, as shown in the following figure, the wrong will burn (such as single voltmeter, it is recommended that the yellow line with black lines together, to prevent outside interference cause ammeter digital flashing)
Technical parameters:
0.Supply voltage: 4.5 30V (wide range)
1.Test voltage: 0 ~ 100V; minimum resolution: 0.1V
2.Test current range: 50A resolution: 0.1A (requires an external shunt)(connect with 50A/75mV shunt) Does not include)
3.Operating Current: <60mA
4.Display: 0.28 "LED, two-color (red and blue) colors
5.Dimensions: 48 × 29 × 21 mm
6.Mounting cutout: 45.5 × 26.5 mm
7.Measurement rate: ≥ 500mS / times
8.Measurement accuracy: 1% (±1 words)
9.Extreme working conditions:
9.1.The minimum Operating voltage: +4.5 V
9.2.Maximum working voltage: +30 V
9.3.Operating temperature: -10 to +65
9.4.Operating Humidity: 10 to 80% (non-condensing)
9.5.Working pressure: 80 ~ 106kPa
9.6.Sun exposure: no direct exposure
1.The small size of the two-color dual instrument.Voltage and current can be displayed on the same screen at the same time
2.This instrument test voltage, current, power supply is taken from the test loop.No additional power supply
3.The the instrument test voltage supply range: DC4.5 ~ 30V,The reverse does not burn,
Note: The maximum input voltage can not exceed 30V, otherwise there is the danger of burned
4.The instrument is equipped with five wiring.Convenient access to car / battery car / motorcycle car line,,Used to monitor the battery voltage,,Grasp the battery voltage state,can also be used for other products, the use of Voltage/current measurement.
Wiring Method:
The instrument with five lines:
Thin black line: Header supply ground
The Thin Red Line: Header powered regular (Note, thin red and black line between the voltage can not exceed 30V)
Thick black lines: public test end
Thick red line: measuring the positive voltage input terminal
Yellow lines: current input terminal; header uses of design, the measuring end of the ground and the ground of the power supply side is the same, it is only then measured the back of the device, as shown in the following figure, the wrong will burn (such as single voltmeter, it is recommended that the yellow line with black lines together, to prevent outside interference cause ammeter digital flashing)
Technical parameters:
0.Supply voltage: 4.5 30V (wide range)
1.Test voltage: 0 ~ 100V; minimum resolution: 0.1V
2.Test current range: 50A resolution: 0.1A (requires an external shunt)(connect with 50A/75mV shunt) Does not include)
3.Operating Current: <60mA
4.Display: 0.28 "LED, two-color (red and blue) colors
5.Dimensions: 48 × 29 × 21 mm
6.Mounting cutout: 45.5 × 26.5 mm
7.Measurement rate: ≥ 500mS / times
8.Measurement accuracy: 1% (±1 words)
9.Extreme working conditions:
9.1.The minimum Operating voltage: +4.5 V
9.2.Maximum working voltage: +30 V
9.3.Operating temperature: -10 to +65
9.4.Operating Humidity: 10 to 80% (non-condensing)
9.5.Working pressure: 80 ~ 106kPa
9.6.Sun exposure: no direct exposure
RS232 To TTL Converter Module MAX232CSE Transfer Chip
Introduction
Thanks for your cooperation!
- It is widely used in radio modification,phone flash,XBOX360 flash,GPS,vehicle detection,
- DVD flash,hard disk repair set-top box upgrade.
- It can be used to program STC MCU,NXP MCU,Renesas MCU,STM32 MCU,N+-2EC MCU
- Communication chip:domestic MAX3232
- Working voltage:3.3V-5.5V
- Port:TX RX VCC GND
Thanks for your cooperation!
2013年9月20日星期五
10A 12V 120W SMPS Regulated Switching Power Supply Driver
1.DC output voltage: 12V
2.Output Voltage Tolerance (Note 2): ± 1%
3.Rated output current: 10A
4.Output current range :0-10A
5.Ripple and noise (Note 3): 100mVp-p
6.Line Regulation (Note 4): ± 0.5%
7.Load stability (Note 5): ±0.5%
8.DC output power:120W
9.Efficiency: 85%
10.DC voltage adjustable range: ±20%
11.Input voltage range: 220V/AC 110V/AC
12.Inrush current: Cold start 18A/115V 36A/230V
13.Leakage current: <0.5mA/240VAC
14.Overload protection: 105% ~ 150% Type: TOLDBACK Reset: auto recovery
15.Overvoltage protection:
16.The high temperature protection: Yes (Built-in thermal)
17.Temperature Coefficient: ±0.03% ℃ (0 ~ 50 ℃)
18.Setup rise hold up time: 200ms, 100ms, 30ms
19.Shock resistance: 10 to 500Hz, 2G 10min. / Cycle time is 60 minutes long, each axis
20.Pressure: between input and output: 1.5KVAC, Input and enclosure: 1.5KVAC output shell: 0.5KVAC
21.Isolation resistance: input and output, input and enclosure, Output and enclosure: 0500VAC/100M Ohms
22.Operating temperature and humidity: -10 ℃ ~ +60 ℃, 20% ~ 90% RH
23.Storage Temperature temperature: -20 ℃ ~ +85 ℃, 10% ~ 95RH
24.Dimensions: 129 * 98 * 40mm
25.Safety standards: meet UL1012 requirements
Note: 1.The above parameters test conditions: 230VAC input, rated load, 25 ℃ 70% RH. Humidity.
2. Tolerance: includes set up tolerance, line stability and load stability (Note 5).
3. the ripple test: 15MHz with A12 "twisted pair, interrupted with 0.1uF & 47uF capacitor short-circuit.
4. the line voltage stability test: full load into the line to the highest voltage minimum voltage.
5. load stability test: The load is from 0% to 100%.
Size:
2.Output Voltage Tolerance (Note 2): ± 1%
3.Rated output current: 10A
4.Output current range :0-10A
5.Ripple and noise (Note 3): 100mVp-p
6.Line Regulation (Note 4): ± 0.5%
7.Load stability (Note 5): ±0.5%
8.DC output power:120W
9.Efficiency: 85%
10.DC voltage adjustable range: ±20%
11.Input voltage range: 220V/AC 110V/AC
12.Inrush current: Cold start 18A/115V 36A/230V
13.Leakage current: <0.5mA/240VAC
14.Overload protection: 105% ~ 150% Type: TOLDBACK Reset: auto recovery
15.Overvoltage protection:
16.The high temperature protection: Yes (Built-in thermal)
17.Temperature Coefficient: ±0.03% ℃ (0 ~ 50 ℃)
18.Setup rise hold up time: 200ms, 100ms, 30ms
19.Shock resistance: 10 to 500Hz, 2G 10min. / Cycle time is 60 minutes long, each axis
20.Pressure: between input and output: 1.5KVAC, Input and enclosure: 1.5KVAC output shell: 0.5KVAC
21.Isolation resistance: input and output, input and enclosure, Output and enclosure: 0500VAC/100M Ohms
22.Operating temperature and humidity: -10 ℃ ~ +60 ℃, 20% ~ 90% RH
23.Storage Temperature temperature: -20 ℃ ~ +85 ℃, 10% ~ 95RH
24.Dimensions: 129 * 98 * 40mm
25.Safety standards: meet UL1012 requirements
Note: 1.The above parameters test conditions: 230VAC input, rated load, 25 ℃ 70% RH. Humidity.
2. Tolerance: includes set up tolerance, line stability and load stability (Note 5).
3. the ripple test: 15MHz with A12 "twisted pair, interrupted with 0.1uF & 47uF capacitor short-circuit.
4. the line voltage stability test: full load into the line to the highest voltage minimum voltage.
5. load stability test: The load is from 0% to 100%.
Size:
2013年9月17日星期二
Waterproof Digital Thermal Probe Sensor DS18B20
20 * 45 mm module circuit 15 mm thick
1, stable performance, measure distance accurate:
Can SRF05 and abroad, such as SRF02 ultrasonic ranging module comparable. Module high precision, blind area (2 cm) super close, stable is the product range to the market success of powerful according to!
2, main technical parameters:
1) the use of voltage: DC5V
2) the static current: less than 2 mA
3) level output: high 5 V
4) level output: bottom 0 V
5) induction Angle: no more than 15 degrees
6) detection range: 2 cm-450 cm
7) high precision: up to 3 mm
3. The wiring way:
VCC, trig (control terminals), echo (receiver), GND
4. Method of use:
A control mouth hair a 10 US above the high level, can wait for high level output receiver mouth. A has an output can open timer time, when the mouth into a low power can be read at ordinary times timer values, where you for the ranging time, can calculate the distance. This will continue the cycle, can reach you move measurement value ~ ~
5. Module working principle:
(1) the IO trigger ranging, to at least 10 us high level signal;
(2) module automatically send eight 40 KHZ of square wave, automatic testing if it has any signals return;
(3) a signal to return to, through the IO output top level, the duration of the high level is from the launch ultrasonic returned to time. Test distance = (high level time * sound velocity (340 M/S)) / 2;
US-100 ultrasonic ranging module can realize 2 cm ~ 4.5 m non-contact ranging function, with a 2.4 ~ 5.5 V of wide voltage input range, static power consumption less than 2 mA, bring their own temperature sensor calibration on the ranging results, and has GPIO, serial ports and so on many kinds of communication mode, inside take watchdog, stable and reliable.
The main technical parameters
- Electrical parameters US-100 Ultrasonic ranging module
- Working voltage DC 2.4V~5.5V
- Static current 2mA
- Working temperature -20~+70degrees
- Output way Level or UART (jumper cap choice)
- Induction Angle Less than 15 degrees
- Detection range 2cm-450cm
- Detecting precision 0.3cm+1%
- UART mode serial interface configuration 9600 baud rate, starting a one, and stop bits a, data bits, eight, and white parity checking, no flow control.
2013年9月16日星期一
TDA7297 Ver A 2*15W Audio Amplifier Board 2-Channel AC/DC 12V
- Volume: 50x50x42mm (L x W x H without potentiometer handle), ultra-small size for any space.
- Over voltage: DC 9-15V, Recommended DC voltage of 12V, current 2A
- Power: 15W +15 W
- Output impedance:4-8 ohm
2nd Round: Get Freebies from www.ICStation.com
|
2013年9月15日星期日
20W DC/DC4.5-24V to 0.93V-20V Step Down Converter Regulator Blue
- Note input voltage range :4.5-24V: 24V to limit maximum voltage, some aggressive otherwise damage
- Output voltage range: 0.93 V-20V (step-down mode, the input must be greater than the output 2V)
- Output Current: 2A Output Output Power: Max 20W
- The ripple frequency: 330Khz about ripple peak to peak: 30mV
- Size: 44mm * 30mm * 20mm Weight: 18 g /
- Voltage indication: Input 4.5-24V, output 0.9-20V
- Switch: for switched digital tube voltage
- Indicator: light digital tube display input voltage, output voltage is off
- Quiescent Current: Typical 25ma (the digital tube color and input voltage affect quiescent current)
Solid State Relay SSR-40DA 40A /250V 3-32VDC
- Input voltage: 3-32VDC
- Output voltage: 24-380VAC
- Output current: 40A
- On voltage: ≤1V
- One-off Time: ≤10ms
- Off leakage Current: ≤2mA
2013年9月12日星期四
New Arrival + 10% Off Coupon + Up to 50% Off on Robot Items
订阅:
博文 (Atom)
-
Introduction Standard double panel design,fine workmanship, board size:38mm X 30mm Use ULN2003 drive chip,50...
-
Share from www.eetimes.com Since the coming of the Raspberry Pi Model B, single-board computers (SBCs) have become a prevalent force in th...
-
The Mega 2560 is a microcontroller board based on the ATmega2560 .It has 54 digital input/output pins (of which 14 can be used as PWM ou...
LED Rotating Globe Planetary Project for STEM Teaching and Soldering Learning
Explore ICStation Latest New Product - DIY Globe Planetary Motion Kit DIY Rotating Universe Model Soldering Practice Kit! The Flashing LE...