Good news all customers!
Top new arrivals this week! Find Amplifier w/ Remote Control, charger modules and DC Motor Driver from icstation! here some details about them:
1) about charger module
Product Introduction:
1.Features:3.6V balanced function
2.Operating Current:58mA
1.Features:3.6V balanced function
2.Operating Current:58mA
Notice:
1.This balanced board is adaptive to lithium battery pack which has no balance charging function.
It can add charging and balanced function to ensure battery pack full of electricity
2.This balanced board has no function of charging or discharging,and it cannot replace the protection board.
When the battery is in the end of full charged,it will discharge by resistor to first fully charged battery,namely shunt and balance function
1.This balanced board is adaptive to lithium battery pack which has no balance charging function.
It can add charging and balanced function to ensure battery pack full of electricity
2.This balanced board has no function of charging or discharging,and it cannot replace the protection board.
When the battery is in the end of full charged,it will discharge by resistor to first fully charged battery,namely shunt and balance function
Product Pictures
2) about Amplifier
Product Introduction:
1.Power Supply Voltage:3.6-5V;3W stereo power amplifier output (BTL output,no common GND,cannot connect with other amplifiers for use)
2.Mul-function:bluetooth receive;hands-free call;fast forward/fast backward;insertation MP3 play;AUX function;radio function
3.Self-equipped with bluetooth audio receive module;after cellphone and bluetooth module has matched successfully,cellphone can play MP3 or bluetooth can send loseless APE file to bluetooth receive module to play;support hands-free call;support playing MP3 document in U-disk or SD card;support radio playing
Bluetooth Function Operation Method:
1.Press "MODE" key to switch state to "BLUE"
2.Open audio device with bluetooth function,search "ZTV-CT02EA" and connects with it
3.Volume can be controlled by external connection sound source device;or long press "PREV" and "NEXT" to adjust vlume
4.When there is call in,short press "Play/Pause"is for answering the phone and long press is for rejecting
5.When you want to call someone or in calling state,short press "Play/pause" is hanging up
6.Note:if current state is mute and there is call in,then it will release the mute state
1.Power Supply Voltage:3.6-5V;3W stereo power amplifier output (BTL output,no common GND,cannot connect with other amplifiers for use)
2.Mul-function:bluetooth receive;hands-free call;fast forward/fast backward;insertation MP3 play;AUX function;radio function
3.Self-equipped with bluetooth audio receive module;after cellphone and bluetooth module has matched successfully,cellphone can play MP3 or bluetooth can send loseless APE file to bluetooth receive module to play;support hands-free call;support playing MP3 document in U-disk or SD card;support radio playing
Bluetooth Function Operation Method:
1.Press "MODE" key to switch state to "BLUE"
2.Open audio device with bluetooth function,search "ZTV-CT02EA" and connects with it
3.Volume can be controlled by external connection sound source device;or long press "PREV" and "NEXT" to adjust vlume
4.When there is call in,short press "Play/Pause"is for answering the phone and long press is for rejecting
5.When you want to call someone or in calling state,short press "Play/pause" is hanging up
6.Note:if current state is mute and there is call in,then it will release the mute state
Product Pictures
3) about the Trigger
Product Introduction:
1.Operating Voltage:6-30V2.Trigger Signal Source:high level trigger (3.0-24V);low level trigger (0-0.2V);on-off value control (passive switch)
3.Output Capacity:can control within DC 30V or AC 220V 5A device
4.Quiescent Current:20mA
5.Operating Current:50mA
6.Service Life:>100,000 times
7.Operating Temperature:-40~85 celsius
8.Specification:6.2*3.8*1.7cm
9.With optocoupler isolation (note:relay output is passive contact,no electricity output;it plays a role of controlling one circuit on/off)
Features: 1.Multi-function:timing;counting;voltage detection;support high level trigger,low level trigger,on-off value control
2.Wide voltage power supply 6-30V
3.One key for emergency stop (STOP key);with reverse connection protection
4.Sleep Mode:after enables,if there is no operation in 5min;then the displayer will be automatically off;any key can awake
5.Set different OP,CL,LOP parameters,and all of them are independent and saved respectively
6.All setting parameters auto saved if power off
Product Pictures
4) aboout the Motor Driver
Product Introduction:
1.Power Supply Voltage: 6.5V-27V (please don't reverse connect or over 27V,or it will damage the module;we recommend that serial connect with 15A fuse on power input port).
2.Double channel motor interface,each channel rated output current 7A;peak current 50A (motor interface shouldn't be short circuit connection;we recommend that serial connect with 10A fuse)
3.Control signal voltage 3-6.5V,respectively enable signal and positive negative rotate control signal
4.Enable signal port (ENA) input PWM speed can be adjustable;PWM frequency range 0-10KHz;PWM minimum pulse width 10us
5.Operating Temperature:-25~80 celsius
6.Specification:55*55*16mm
7.Installation Hole Diameter:3mm
Features:
1.Double H bridge,can drive two motors at the same time;single channel 7A current;high power
2.Wide Voltage Input:6.5V-27V
3.Signal optocoupler isolation input,IO port can directly control without interference
4.Undervoltage protection
5.High power and TVS and electrostatic discharge circuit;not only repress instant interfere pulse and electrostatic,but also enhance EMC performance
1.Power Supply Voltage: 6.5V-27V (please don't reverse connect or over 27V,or it will damage the module;we recommend that serial connect with 15A fuse on power input port).
2.Double channel motor interface,each channel rated output current 7A;peak current 50A (motor interface shouldn't be short circuit connection;we recommend that serial connect with 10A fuse)
3.Control signal voltage 3-6.5V,respectively enable signal and positive negative rotate control signal
4.Enable signal port (ENA) input PWM speed can be adjustable;PWM frequency range 0-10KHz;PWM minimum pulse width 10us
5.Operating Temperature:-25~80 celsius
6.Specification:55*55*16mm
7.Installation Hole Diameter:3mm
Features:
1.Double H bridge,can drive two motors at the same time;single channel 7A current;high power
2.Wide Voltage Input:6.5V-27V
3.Signal optocoupler isolation input,IO port can directly control without interference
4.Undervoltage protection
5.High power and TVS and electrostatic discharge circuit;not only repress instant interfere pulse and electrostatic,but also enhance EMC performance
Product Pictures
没有评论:
发表评论